Showing posts with label Wood working. Show all posts
Showing posts with label Wood working. Show all posts

Wednesday, February 11, 2015

DIY: Building a Book of Wood

Making A Game Plan and Building a Book

The more I thought about this book I want to make, the more I felt I needed a game plan, or blueprint for what I was going to be doing. So I started to draw out what I wanted to make. I knew the material I was going to be using was going to be about 1/2 an inch thick, and I wanted to make sure to factor that in, as well as be able to allow my book to hold about 200-300 pages.

So this is how I started the process:
  1. I measured the ream of paper I have. 500 pages = 2 inches.
  2. The size of paper to be used is 8 1/2 inches by 11 inches.
  3. I want there to be about 1/4 - 1/2 inch of space between the edge of the page and the edge of the book
  4. Decide if you want to be able to add or remove pages, in my case I do
  5. I drew a rough sketch of what I thought the book should look like

  6. With Measurements know, you are able select the wood you want to use.
  7. I am not very handy with power tools, so I took a simple approach to this. I went to Menards, and found some craft wood. They have many sizes and shapes. I was able to find a bit that was 12 mm (1/2") x 12" x 24". We checked the piece to make sure it was square before we left the store. This would mean we would only have to cut the wood vertically to make the book. This was so very VERY helpful!!
  8. Mark off the measurements needed to be cut, and make sure to take into account "waste". I classify waste as the wood the saw blade eats up to make the cut. Usually the saw blade will use about 1/8 of an inch, give or take.
  9. Once all the cuts have been made, sand and smooth all the edges and make sure everything is still square and lines up.
  10. I started with the spine being it required the most work. I the two sides and the back bone up, marked off where the screws needed to go on all 3 bits, and used my dremel to pre-drill the holes to avoid splitting the wood. We used solid brass screws, about an inch long.
  11. To hold the papers in the book, I used scrapbook album posts from Hobby Lobby, with extensions  to hold the correct number of pages. Once the spin was together, I used a drill with a bit just little bigger than the posts, and drill through both sides to make sure they would line up.
  12. Once the spine was screwed together and the posts in, placement of the hinges needed to be decided. I picked simple but decorative hinges from Lowe's. Once done, I used the dremel to pre-drill the holes and attached the hinges to the spine and to the covers.
This is as far as I have made it with my book. I am very excited about how well it turned out.



There is still detail work to be done on the cover and spine. I plan to work more on this over the weekend. Should be able to post more photos after I am finished and there is paper in the book.

Filling the Book

I have been reading a few books over the years, and taking notes. My notes have been typed, up I could always read what I had written. I know sometimes my hand writing can be pretty bad. I took all the separate documents, and combined them into one word document, and printed them (front to back) on my home printer. I found the easiest way to accomplish this was to set up the document with mirrored margins, so that I could allow for enough space for the binding/studs that hold the paper in. 

Being that I wanted to be able to still add to this book as I go along, I printed up some blank lined pages. I made the lined pages in word, as a table with horizontal boarders only. I have it available online here. I made the page to have the same mirror margins as the rest of my pages. This way when I have the time, I can take notes from my readings, and replace the hand written notes with typed ones as needed. The last step to putting the pages in the book is to drill the holes in the paper. Once I have done this I am able to put them in the book and have my journal fully functional and ready for me to use.

The next step to this process, is to create a cover design for the book, and print it out. Once I have printed it out, I will use graphite paper to transfer the design to the wood, then use the dremel to engrave the design. I am going to try to do the same process with the spine and back as well. I am really excited to see how this process turns out. Now just to figure out what design to put on the cover. I feel that is going to be the hardest part of the process, trying to figure out what kind of creative idea I want to be on my book forever.
I this brings me to the conclusion that I have completed several steps to this project, but I am not sure what I am going to do this when I am finished.

Feeling Accomplished

When I was able to finish my book, I engraved the design I printed traced. Once I design was on the book, it was finally starting to look like what I had been envisioning. I started to get very excited and couldn't stop working on it. One word of caution make sure to take into account the size of the cuts and shapes. 

As I finished the engraving, and looked at the work I have done, I quickly realized it still looked very rough, so I used a the green rounded bit (not sure what it is called, but looked it up online this looks like it). With this bit, I smoothed the engraving so that there was no harsh edges
on top, then used a sander to smooth the whole thing down. I showed a few people in my house who didn't quite think I could make my vision come true and they are very impressed with my hard work, and my ability with power tools.

Old English lettering is very time consuming and difficult to engrave. I would suggest only doing the first letter of something in it, then use a different font for the rest of the words. But it did make the cover look amazing!

I was also able to get all my pages in the book. I easiest way to put pages in is to remove the top of the spine, and put all the pages in you want, and then screw it all back together. I ended up being able to get about 300 pages in my book, which excites me, because now I can add so much more to it!

Overall, I am very happy with the end product. I have a few bits of scrap wood left, so I am going to test some stains on it, and see which I like best. Staining it will be the last step to finishing my amazing book.
 

FINAL PRODUCT




I am completely in love with how the book turned out. I am using this for all my final copies of items. I have another cloth bound book I use to take notes or write thoughts/ideas/ processes down in. Then I take the time to clean them up, and fine tune them and put them in this book.

I hope this helps with a DIY project of your own!!! Please feel free to leave any comment, questions, or suggestions on my Facebook, Twitter, Pinterest, Tumblr, Youtube, Google+, or Email me!! I always look forward to feedback!!



Wednesday, November 12, 2014

DIY: Dremel Plaque

Dremel Plaque for VMC Friends

I have made a few plaques for some friends of ours in the Veterans Motorcycle Club. I have really come to enjoy my dremel and all the items I have been able to make with it.

I started all the plaques with wood base I purchased from Hobby Lobby. I have found they seem to have the best selection in sizes and the wood is nice quality, and the dremel has no issues cutting it. They have a lot of designs to choose from - check them out!




Larger - 7x9






I used Word to create my design for the plaque. Even if it is not completely what I am wanting to put on the plaque, This will at least give me the sizes of the items I want to put on the plaques. After I have the design, I print int out, and then take it to the right size of Trace-It Transfer Paper. 

I place all the printed designs on the transfer paper on the plaque, and move them around to where they look best. Once that position has been found, I tape the transfer paper down. I use the embossing styles to trace the design on the the plaque.


<-- Design on the transfer paper


Transferred Design -->




Once I have the design on the plaque, I use the my dremel to cut out the design. Once I have cut the design into the wood, I stain it, and paint the design in.

I used a ash grey wood stain. I put it on thick, they whipped it off, to give more of a distressed look. I painted around the outside of the goose black, to allow it to pop a little more on the stained background. All the paint used was basic art paint, I believe acrylic from Hobby Lobby. To finish off everything off, I sprayed a couple coats of clear coat.

Final Products:












On the back of the plaques I screw on a Saw tooth hanger. So that they are able to hang the plaques. I hope that everyone enjoys. Please let me know if there is any projects like this that you would like to see. Or if there is any more details you would like on how I completed these. The next dremel project I will video record so that everyone can see how I dremel.

As always, please check out my Facebook, Twitter, Pinterest,  Tumblr, Youtube, and Google+, or Email me!! I always look forward to feedback!!