Showing posts with label DIY. Show all posts
Showing posts with label DIY. Show all posts

Wednesday, February 11, 2015

DIY: Building a Book of Wood

Making A Game Plan and Building a Book

The more I thought about this book I want to make, the more I felt I needed a game plan, or blueprint for what I was going to be doing. So I started to draw out what I wanted to make. I knew the material I was going to be using was going to be about 1/2 an inch thick, and I wanted to make sure to factor that in, as well as be able to allow my book to hold about 200-300 pages.

So this is how I started the process:
  1. I measured the ream of paper I have. 500 pages = 2 inches.
  2. The size of paper to be used is 8 1/2 inches by 11 inches.
  3. I want there to be about 1/4 - 1/2 inch of space between the edge of the page and the edge of the book
  4. Decide if you want to be able to add or remove pages, in my case I do
  5. I drew a rough sketch of what I thought the book should look like

  6. With Measurements know, you are able select the wood you want to use.
  7. I am not very handy with power tools, so I took a simple approach to this. I went to Menards, and found some craft wood. They have many sizes and shapes. I was able to find a bit that was 12 mm (1/2") x 12" x 24". We checked the piece to make sure it was square before we left the store. This would mean we would only have to cut the wood vertically to make the book. This was so very VERY helpful!!
  8. Mark off the measurements needed to be cut, and make sure to take into account "waste". I classify waste as the wood the saw blade eats up to make the cut. Usually the saw blade will use about 1/8 of an inch, give or take.
  9. Once all the cuts have been made, sand and smooth all the edges and make sure everything is still square and lines up.
  10. I started with the spine being it required the most work. I the two sides and the back bone up, marked off where the screws needed to go on all 3 bits, and used my dremel to pre-drill the holes to avoid splitting the wood. We used solid brass screws, about an inch long.
  11. To hold the papers in the book, I used scrapbook album posts from Hobby Lobby, with extensions  to hold the correct number of pages. Once the spin was together, I used a drill with a bit just little bigger than the posts, and drill through both sides to make sure they would line up.
  12. Once the spine was screwed together and the posts in, placement of the hinges needed to be decided. I picked simple but decorative hinges from Lowe's. Once done, I used the dremel to pre-drill the holes and attached the hinges to the spine and to the covers.
This is as far as I have made it with my book. I am very excited about how well it turned out.



There is still detail work to be done on the cover and spine. I plan to work more on this over the weekend. Should be able to post more photos after I am finished and there is paper in the book.

Filling the Book

I have been reading a few books over the years, and taking notes. My notes have been typed, up I could always read what I had written. I know sometimes my hand writing can be pretty bad. I took all the separate documents, and combined them into one word document, and printed them (front to back) on my home printer. I found the easiest way to accomplish this was to set up the document with mirrored margins, so that I could allow for enough space for the binding/studs that hold the paper in. 

Being that I wanted to be able to still add to this book as I go along, I printed up some blank lined pages. I made the lined pages in word, as a table with horizontal boarders only. I have it available online here. I made the page to have the same mirror margins as the rest of my pages. This way when I have the time, I can take notes from my readings, and replace the hand written notes with typed ones as needed. The last step to putting the pages in the book is to drill the holes in the paper. Once I have done this I am able to put them in the book and have my journal fully functional and ready for me to use.

The next step to this process, is to create a cover design for the book, and print it out. Once I have printed it out, I will use graphite paper to transfer the design to the wood, then use the dremel to engrave the design. I am going to try to do the same process with the spine and back as well. I am really excited to see how this process turns out. Now just to figure out what design to put on the cover. I feel that is going to be the hardest part of the process, trying to figure out what kind of creative idea I want to be on my book forever.
I this brings me to the conclusion that I have completed several steps to this project, but I am not sure what I am going to do this when I am finished.

Feeling Accomplished

When I was able to finish my book, I engraved the design I printed traced. Once I design was on the book, it was finally starting to look like what I had been envisioning. I started to get very excited and couldn't stop working on it. One word of caution make sure to take into account the size of the cuts and shapes. 

As I finished the engraving, and looked at the work I have done, I quickly realized it still looked very rough, so I used a the green rounded bit (not sure what it is called, but looked it up online this looks like it). With this bit, I smoothed the engraving so that there was no harsh edges
on top, then used a sander to smooth the whole thing down. I showed a few people in my house who didn't quite think I could make my vision come true and they are very impressed with my hard work, and my ability with power tools.

Old English lettering is very time consuming and difficult to engrave. I would suggest only doing the first letter of something in it, then use a different font for the rest of the words. But it did make the cover look amazing!

I was also able to get all my pages in the book. I easiest way to put pages in is to remove the top of the spine, and put all the pages in you want, and then screw it all back together. I ended up being able to get about 300 pages in my book, which excites me, because now I can add so much more to it!

Overall, I am very happy with the end product. I have a few bits of scrap wood left, so I am going to test some stains on it, and see which I like best. Staining it will be the last step to finishing my amazing book.
 

FINAL PRODUCT




I am completely in love with how the book turned out. I am using this for all my final copies of items. I have another cloth bound book I use to take notes or write thoughts/ideas/ processes down in. Then I take the time to clean them up, and fine tune them and put them in this book.

I hope this helps with a DIY project of your own!!! Please feel free to leave any comment, questions, or suggestions on my Facebook, Twitter, Pinterest, Tumblr, Youtube, Google+, or Email me!! I always look forward to feedback!!



Wednesday, January 14, 2015

DIY: Homemade Luandry Soap

Making your own Laundry Soap

I have found that one thing I completely ENJOY doing is making laundry soap for my family. Not only is it cheaper, it is something I am able to involve my son. I am also to able to ensure that there is nothing harmful in our laundry. I have seen several people posting on Pinterest about it, and finally gave in and tried my own recipe for the powder soap. I always was able to re-purpose several containers to help reduce the need to purchase new.

I started out with a bit of shopping. My list included washing soda, borax, a bar of fels-naptha, cheese grater. I re-purposed an old mayo jar, pickle jar, and large mayo container.I  suggest once you open the washing soda & borax that you place them in air tight containers because they tend to become a hard mass that you have to grate back into a powder. And always keep the soap in an air tight container after you make it.

Recipe:
  • 1 bar Fels-Naptha
  • 1 1/2 cup Borax
  • 1 1/2 cup Washing Soda
I measure out the Borax and washing soda, and place into my storage container. I use and old Tide box to grate the bar of soap. Once I have the full bar grated, I place all the shavings into the storage container. The the only thing I was scared the first time I made this soap was that I was grating it wrong, or that not fine enough. So I wanted to make sure I showed what my grated soap looked like. I have had no issues with this in our washing machine. Been using it now for about 6 months.
Once I have all three ingredients in the container, I place the lid on it and let my son shake shake shake it. Usually I stop her a few times to check to make sure it is mixing well. When doing laundry we use only one tablespoon per load. This soap does work well enough to clean the messes my 3 year old can create as well as the greasy Harley mess my husband makes. I switched to my own soap but never told anyone in the house. After about 3 week, I asked if.laundry was still clean and good- no one seemed to notice the change.



Thursday, December 18, 2014

DIY: Getting Kids Involved

Fun for all Ages

While enjoying Pinterest, I have found so many great kids craft & toy ideas. We are getting ready to start some of these for Christmas presents.

Several of the items I came across involved crayons, my sons favorite new thing. We were doing a lot of the crayon magic so that he can only write on the "special" paper. That has started to cost a lot because he is all about trying to eat the makers. One of the projects I found could have a couple uses. One is actual use for your own child, other is to use as valentines day card gifts. This is a great idea for the left over or broken crayons too. Making sure you get every penny out of them. Cut the pieces up, place in a mold of some sort, bake at 203* for 15 min, and you get super cute shaped multicolored crayons!!

Another idea along the same lines is to take crayons, cut them up melt them in the microwave for 3-5 mins, then pour into an empty glue stick. This way your able to have a "safe" crayon that will not bet broken as easy, as well as a bit harder for the young ones to possible eat. Its always great to allow the them to express there creativity.

Crayons are just one part of the amazing things I found. A great way to make use of all the the "extra" leftovers, is to allow your kids paint with the paper towel and toilet paper rolls! You can cut longer tubs up so you can get more uses out of them. This allows your young one to explore creating with different mediums. As long as you use water based paints clean up should be fairly simple. I did find online a way to make your own finger paints, that way your able to save even more money. They can paint on an old box, paper, or just about anything else you have just laying around. Once they have completed the masterpiece, You can place it in a frame or attach twin or yarn to it to hang on the wall to show off the great.

On a related note, you can also create homemade window paint. This
is great for kids are they start to get a bit older and can be trusted just a bit more. This is a great idea if you have patio doors. You can let the kids be outside and paint, then clean up is SO much easier.

The last idea I found was a great idea for younger children who are still to young for the prior ideas. Create there own light show, all you need is a box, and some Christmas lights. Cut some holes in the top of the box, and stick the lights through them. Place some pillows and a blanket in there. This gives a fun place for them to lay and relax, and look at the "stars". My son would just LOVE it. We are going to have this finished for him for Christmas morning. I am thinking it will be his favorite place to hang out.

Tuesday, December 16, 2014

DIY: Homemade Play-Doh!!

I found this recipe online, and knew I HAD to try it out. I have been looking for a project that I could include my son in, and this was it. I remember being younger and playing with Playdough, building colorful creations to show my parents. But it always tasted funny (I don't really remember the taste, I just know kids eat everything and Playdough does not look all that yummy).

I found the recipe on another blog (ArtsyFartsyMama.com) - and I want to make sure to give her credit. Her directions were perfect!!


Ingredients:
1 cup water, 2 tbsp vegetable oil, 1 cup flour, 1/4 cup salt, 2 tbsp cream of tartar, gel food coloring

Directions:
Pour the water and vegetable oil in a saucepan. Add in the flour, salt, cream of tarter and a teaspoon or two of gel food coloring. Lightly stir together to combine.
*The dough will end up being about the same color that it is now, so add more food coloring now if you want the color to be richer/brighter.

Cook the mixture over medium heat, stirring constantly. It should be done in about 4-5 minutes. 

Because you might panic and think you've ruined it, here is a breakdown of what it looks like throughout the cooking process:
• Minute 1: The mixture will combine, and look smooth and beautiful!
• Minute 2: You'll start to get chunks. Make sure to keep scraping the bottom and edges of the pan to prevent any pieces from burning.
• Minute 3: This is where you might begin to worry that you've messed it up. Looks like a clumpy mess. Don't panic! Just keep stirring!!
• Minute 4: The dough will start to form into a ball. You'll know when it's ready when it's not sticky and pulls away from the pan. You can test by pressing the dough with your fingers. It will be hot!

Remove the dough from the pan and place on a plate to cool.

Once cool, knead the dough. This can be done by you or little helpers!

To store, wrap the dough in plastic wrap and place in a sealed container.

A few notes:
Each batch makes about 2 cups of dough. You need to make a new batch for each color. It took me less than an hour to make all 6 batches.
Surprisingly, the food coloring doesn't come off on your hands at all.
The dough is safe to eat, but it is disgusting!
Buy more cream of tartar than you think you'll need. I got 2 1/2 batches from one 1.5 oz container.
Regular liquid food coloring will also work, but I think the gel makes the color a little more vibrant. 


Wednesday, November 12, 2014

DIY: Dremel Plaque

Dremel Plaque for VMC Friends

I have made a few plaques for some friends of ours in the Veterans Motorcycle Club. I have really come to enjoy my dremel and all the items I have been able to make with it.

I started all the plaques with wood base I purchased from Hobby Lobby. I have found they seem to have the best selection in sizes and the wood is nice quality, and the dremel has no issues cutting it. They have a lot of designs to choose from - check them out!




Larger - 7x9






I used Word to create my design for the plaque. Even if it is not completely what I am wanting to put on the plaque, This will at least give me the sizes of the items I want to put on the plaques. After I have the design, I print int out, and then take it to the right size of Trace-It Transfer Paper. 

I place all the printed designs on the transfer paper on the plaque, and move them around to where they look best. Once that position has been found, I tape the transfer paper down. I use the embossing styles to trace the design on the the plaque.


<-- Design on the transfer paper


Transferred Design -->




Once I have the design on the plaque, I use the my dremel to cut out the design. Once I have cut the design into the wood, I stain it, and paint the design in.

I used a ash grey wood stain. I put it on thick, they whipped it off, to give more of a distressed look. I painted around the outside of the goose black, to allow it to pop a little more on the stained background. All the paint used was basic art paint, I believe acrylic from Hobby Lobby. To finish off everything off, I sprayed a couple coats of clear coat.

Final Products:












On the back of the plaques I screw on a Saw tooth hanger. So that they are able to hang the plaques. I hope that everyone enjoys. Please let me know if there is any projects like this that you would like to see. Or if there is any more details you would like on how I completed these. The next dremel project I will video record so that everyone can see how I dremel.

As always, please check out my Facebook, Twitter, Pinterest,  Tumblr, Youtube, and Google+, or Email me!! I always look forward to feedback!!

Friday, November 7, 2014

First of Many posts to come

I am going to be giving this a hard time this time.

I am really wanting to try to start blogging about things that matter to me. I am going to start off with a minimum of one post a week, and each week of the month with be on a different topic.



My first post will be about the DIY projects I have been working on, or want to work on. I have a very crafty side, and want to be able to share with everyone the projects I find on Pinterst and how they turn out when I try my hand. I hope to be able to also share on my social media links and topics to go with this through out the week.



My second week will be a bit of a self help/pet peeve type of post. I wanted to post about things that have helped me along the way and things that are really just bugging the crap out of me! I will share different images on my Tumbler and Facebook pages, through out the week as the relate to the blog post. I have been diagnosed with Bi-Polar, and it has become a daily struggle. I feel like there are others like me out there, and they need to know it is possible to be a success  in life.



The third week, I want to try to do a post on something technology related. Might be a walk through on how to do a process (mail merge or something) or how to setup a router, or a review of a new techy item I have acquired. I hope to be able to use some screen shots and video captures to make the walk throughs easier to follow, and will post them on YouTube. I have 3 college degrees: Associates in Applied Business, Associates in Web Development, and Bachelors in Technology Management. I really want to be able to share my knowledge with others and hope to be a help to them. I hope to be able to share some great info on Twitter with everyone as well.



The 4th week of the month I want to do a spiritual post. Share with everyone a bit about my beliefs and how I am working to further my knowledge of my systems. I am a Wiccan Witch, and it is always a process to keep learning and knowing more about everything. I think it would amazing to share that with others who are thinking about this path. I hope to share Facebook pages, and other Websites that might interest others as well as photos through out the week on Tumbler.

On the occasion that there is a 5th week in the month, I will do a "By Request" post. I will let the reads pick the topic for the week.

Please give me your ideas and feedback

As many can guess, Annabelle is not my real name, but I am hoping that by using my Wiccan name, I might be able to share some very honest facts and experiences without to much blow back in my normal life. 

Contact me!!

Please feel free to contact me on any of my social networks (listed in the about me section as well). I am on:
Facebook - Annabell Moonbeam
Twitter - @AnnabelMoonbeam
Pintrest - Annabelle Moonbeam

You can also email me too!! annabellel.moonbeam@gmail.com

I will do my best to respond to all inquires and questions.